These crepe streamer poppies are classy, elegant and very easy to make. This project requires no special skills or experience making paper flowers. Each step is very easy. Your flowers will turn out beautiful.
- Crepe paper streamers – 1 roll (1 – 3/4″ wide). You can make dozens of flowers with a single roll. I recommend white crepe paper because white is very forgiving. Glue spills don’t show up. When you are getting better (you will be an expert in no time), try using colored streamers.
- Spun cotton balls – white – 15 mm diameter (.59 inches). 1 ball per flower.
- Sharp scissors.
- Low temperature glue gun and glue sticks.
- Stem wire. The wire I used for these flowers is 18 gauge and 18″ long. I found it at Michaels.
- Floral tape.
- A small piece of cardboard to make your petal template. Or you can just print my template on regular paper and cut it out (link below).[/threecol_two_last] [divider_flat]
[box type=”note”]Important: I recommend using a low temperature glue gun so you don’t burn your fingers.[/box]
Step 1: Gather all your materials. I recommend to set up in a location where there is no air circulating (the petals fly off easily).
Step 2: Make your petal template. You can download the template (link below) or just copy from the picture. (It is not an exact science). My petals are 1-11/16″ wide and 1-1/2″ tall.
[box type=”download”]Click here to Download the petal template. When printing, make sure to set the scale at 100%. [/box]
Step 3: Cut out 6 identical petals. Fold the crepe streamer 6 times onto itself. Outline the shape of a petal on the top layer. Cut out all layers at once with a sharp pair of scissors.
Step 4: Glue the spun cotton ball onto the stem wire. (reminder: use a low temperature glue gun or you will burn yourself). Pour a generous amount of glue over the hole and immediately insert the stem (all spun cotton balls have a little hole). Wait 5 seconds for the glue to become moldable. Quickly, shape the glue into a cone shape with your index and thumb fingers.
It is important to create a little “cone” of glue under the ball.
It will make for a nice surface to glue the petals to.
Step 5: Make the support cone a little bigger by adding more glue. Pour glue all around it, wait 5 seconds for the glue to become moldable, press down with your thumb and index fingers to shape as a cone.
Step 6: Add petal #1. Pour a horizontal bead of glue about 3/8″ long right at the junction between the spun cotton ball and the support cone. Line up the bottom of the petal with the bottom of the cone and press the petal against the glue. The petal should cup around the ball.
Step 7: Add petal #2. Petal #2 needs to overlap petal #1 by a little bit (about 1/3 “).
Step 8: Add petal #3. Petal #3 should fit right between petal #1 and petal #2, overlapping them a little bit on each side. Glue into place using the same technique as for petal #1 and 2. When done, your three first petals should look evenly distributed around the ball.
Step 9: Add petal #4. Pour a 3/4″ horizontal bead of glue across petals #1 and 3. This glue line should be a little bit higher up (maybe 1/4″) than the first 3 petals glue lines. Position petal #4. Press down against the glue. Petal #4 should cup around the ball
Step 10: Add petal #5. Following the same technique, glue petal #5 exactly between petals #2 and 3.
Step 11: Add petal #6. Still with the same technique, glue petal #6 exactly between petals #3 and 1.
Step 12: Apply the first piece of floral tape. We want to give the flower a clean look by covering the very bottom of the petals and hiding all the imperfections. Cut a 5″ long piece of tape. Start twisting the tape around the stem at about 1/2″ below the flower. Go about 2 turns. Then work your way up the stem until the tape covers the very bottom of the petals. Stay up for about 3 turns. Work your way down until you run out of tape.
Step 13: Finish wrapping up the stem with floral tape. Cut a 16″ long piece of tape, start where you ended, and work your way down. Maintain a sharp angle and moderate tension.
This is it
You made it!
If you wish, try to make another paper flower. You will be an expert in no time. For variety, you can try different color crepe paper rolls. You can also paint the spun cotton balls. You can even cheat a little and buy pre-cut fabric petals at the craft store.
I hope you enjoyed this tutorial and found some inspiration for your next projects. As usual, do not hesitate to get in touch if you have any questions.
Same technique, more project ideas:
Red fabric petal version
Perfect for Valentine’s day
Bamboo stick version
With blue mason jar
Glitter mod podge dipped
Rainbow crepe streamers